vincent's Blog

SYNOPSIS
mt [-h] [-f device] operation [count] [arguments...]

DESCRIPTION
This manual page documents the tape control program mt. mt performs the given operation, which must be one of the
tape operations listed below, on a tape drive. The commands can also be listed by running the program with the -h
option. The version of mt is printed with the -v or --version option. The path of the tape device on which to oper-
ate can be given with the -f or -t option. If neither of those options is given, and the environment variable TAPE
is set, it is used. Otherwise, a default device defined in the file /usr/include/sys/mtio.h is used.

Some operations optionally take an argument or repeat count, which can be given after the operation name and
defaults to 1. The postfix k , M , or G can be used to give counts in units of 1024, 1024 * 1024, or 1024 * 1024 *
1024, respectively.

The available operations are listed below. Unique abbreviations are accepted. Not all operations are available on
all systems, or work on all types of tape drives.

fsf Forward space count files. The tape is positioned on the first block of the next file.

fsfm Forward space count files. The tape is positioned on the last block of the previous file.

bsf Backward space count files. The tape is positioned on the last block of the previous file.

bsfm Backward space count files. The tape is positioned on the first block of the next file.

asf The tape is positioned at the beginning of the count file. Positioning is done by first rewinding the tape
and then spacing forward over count filemarks.

fsr Forward space count records.

bsr Backward space count records.

fss (SCSI tapes) Forward space count setmarks.

bss (SCSI tapes) Backward space count setmarks.

eod, seod
Space to end of valid data. Used on streamer tape drives to append data to the logical end of tape.

rewind Rewind the tape.

offline, rewoffl, eject
Rewind the tape and, if applicable, unload the tape.

retension
Rewind the tape, then wind it to the end of the reel, then rewind it again.

weof, eof
Write count EOF marks at current position.

wset (SCSI tapes) Write count setmarks at current position (only SCSI tape).

erase Erase the tape.

status Print status information about the tape unit. (If the density code is "no translation" in the status output,
this does not affect working of the tape drive.)

seek (SCSI tapes) Seek to the count block on the tape. This operation is available on some Tandberg and Wangtek
streamers and some SCSI-2 tape drives. The block address should be obtained from a tell call earlier.

tell (SCSI tapes) Tell the current block on tape. This operation is available on some Tandberg and Wangtek
streamers and some SCSI-2 tape drives.

setpartition
(SCSI tapes) Switch to the partition determined by count. The default data partition of the tape is num-
bered zero. Switching partition is available only if enabled for the device, the device supports multiple
partitions, and the tape is formatted with multiple partitions.

partseek
(SCSI tapes) The tape position is set to block count in the partition given by the argument after count. The
default partition is zero.

mkpartition
(SCSI tapes) Format the tape with one (count is zero) or two partitions (count gives the size of the second
partition in megabytes). The tape drive must be able to format partitioned tapes with initiator-specified
partition size and partition support must be enabled for the drive.

load (SCSI tapes) Send the load command to the tape drive. The drives usually load the tape when a new cartridge
is inserted. The argument count can usually be omitted. Some HP changers load tape n if the count 10000 + n
is given (a special funtion in the Linux st driver).

lock (SCSI tapes) Lock the tape drive door.

unlock (SCSI tapes) Unlock the tape drive door.

setblk (SCSI tapes) Set the block size of the drive to count bytes per record.

setdensity
(SCSI tapes) Set the tape density code to count. The proper codes to use with each drive should be looked
up from the drive documentation.
densities
(SCSI tapes) Write explanation of some common density codes to standard output.

drvbuffer
(SCSI tapes) Set the tape drive buffer code to number. The proper value for unbuffered operation is zero
and "normal" buffered operation one. The meanings of other values can be found in the drive documentation
or, in the case of a SCSI-2 drive, from the SCSI-2 standard.

compression
(SCSI tapes) The compression within the drive can be switched on or off using the MTCOMPRESSION ioctl. Note
that this method is not supported by all drives implementing compression. For instance, the Exabyte 8 mm
drives use density codes to select compression.

stoptions
(SCSI tapes) Set the driver options bits for the device to the defined values. Allowed only for the supe-
ruser. The bits can be set either by ORing the option bits from the file /usr/include/linux/mtio.h to count,
or by using the following keywords (as many keywords can be used on the same line as necessary, unambiguous
abbreviations allowed):

buffer-writes buffered writes enabled

async-writes asynchronous writes enabled

read-ahead read-ahead for fixed block size

debug debugging (if compiled into driver)

two-fms write two filemarks when file closed

fast-eod space directly to eod (and lose file number)

no-wait don’t wait until rewind, etc. complete

auto-lock automatically lock/unlock drive door

def-writes the block size and density are for writes

can-bsr drive can space backwards as well

no-blklimits drive doesn’t support read block limits

can-partitions drive can handle partitioned tapes

scsi2logical seek and tell use SCSI-2 logical block addresses instead of device dependent addresses

sysv enable the System V semantics
stsetoptions
(SCSI tapes) Set selected driver options bits. The methods to specify the bits to set are given above in
the description of stoptions. Allowed only for the superuser.

stclearoptions
(SCSI tapes) Clear selected driver option bits. The methods to specify the bits to clear are given above in
description of stoptions. Allowed only for the superuser.

stwrthreshold
(SCSI tapes) The write threshold for the tape device is set to count kilobytes. The value must be smaller
than or equal to the driver buffer size. Allowed only for the superuser.

defblksize
(SCSI tapes) Set the default block size of the device to count bytes. The value -1 disables the default
block size. The block size set by setblk overrides the default until a new tape is inserted. Allowed only
for the superuser.

defdensity
(SCSI tapes) Set the default density code. The value -1 disables the default density. The density set by
setdensity overrides the default until a new tape is inserted. Allowed only for the superuser.

defdrvbuffer
(SCSI tapes) Set the default drive buffer code. The value -1 disables the default drive buffer code. The
drive buffer code set by drvbuffer overrides the default until a new tape is inserted. Allowed only for the
superuser.

defcompression
(SCSI tapes) Set the default compression state. The value -1 disables the default compression. The compres-
sion state set by compression overrides the default until a new tape is inserted. Allowed only for the supe-
ruser.

sttimeout
sets the normal timeout for the device. The value is given in seconds. Allowed only for the superuser.

stlongtimeout
sets the long timeout for the device. The value is given in seconds. Allowed only for the superuser.

stsetcln
set the cleaning request interpretation parameters.

mt exits with a status of 0 if the operation succeeded, 1 if the operation or device name given was invalid, or 2
if the operation failed.

AUTHOR
The program is written by Kai Makisara .

COPYRIGHT
The program and the manual page are copyrighted by Kai Makisara, 1998-2004. They can be distributed according to
the GNU Copyleft.

SEE ALSO
st(4)